Target Type Pilot
This pilot burner can be used on all types of burner systems where wind and port blowback is not a factor. It energizes the thermocouple and ignites the main flame front. A threaded coupler holds the thermocouple in perfect position. This burner is made from steel. Some pilots of this style are made, in part, of aluminum which can melt from the high ambient port temperatures of stoneware kilns. NOTE: May be unstable at pressures greater than 2 PSI.
Price: $42.95
|
Blower Speed Control
This solid state speed control is designed for use with PSC (permanent split capacitor) or shaded pole blowers like the ones we use on our MB POWER BURNERS. Ordinary dimmer switches can damage the motors mentioned above.
Price: $29.50
|
Rectifying Pilot
This pilot burner can be used on burner systems where wind and port blowback is not a factor and that use an intermittent pilot control (see below). This burner is made from steel. Some pilots of this style are made, in part, of aluminum which can melt from the high ambient port temperatures of stoneware kilns. NOTE: May be unstable at pressures greater than 2 PSI.
Price: $44.50 |
Flame Retention Nozzles
"AN" type nozzles are open flame heads designed for high capacities with good flame retention characteristics. High capacities are made possible by large burner area in relation to flame tube size. "AN" nozzles are scientifically designed to handle rich gas-air mixtures while using relatively low mixture pressures. Drilled pilot holes around the opening keep the main flame from "blowing off" the burner nozzle. Increases in flame actually improve the piloting action. Other sizes than those listed are available. Please call for additional sizes and price. Sizes apply to the thread size of pipe that the nozzle is screwed onto. See the bottom of our Technical Dowload page for a printable form that measures male and female pipe sizes.
|
|
Pipe
Size
|
"D"
diam
|
"L"
length
|
"O"
opening
|
Price |
1 1/2"
|
2 5/8"
|
2 1/4"
|
1 7/16"
|
$62.50
|
2"
|
3 1/4"
|
2 7/16"
|
1 7/8"
|
$69.50
|
2 1/2"
|
3 7/8"
|
2 3/4"
|
2 1/2"
|
$82.00
|
|
Spark Ignition Module
The CAM-STAT P120 is used to protect a standing pilot from being extinguished. The unit works by emitting very intense, pulsed electrical arcs. The electrode senses a flame outage in less than 1 second and begins pulsing at 300 cycles per minute until the flame is re-established. It's automatic and instant lighting makes this unit a very safe and trouble-free addition. Must be wired to a properly grounded 120Vac line. (cannot use GFI circuitry)
Price: $ 87.50
|
Heavy Duty Electrode & Wire
For those requiring a heavier and longer (6") electrode, this unit can be used with the Cam-stat P120 above. A more durable electrode than supplied with the Cam-Stat. Heavy silicon, high-temp wire with spark plug cage is the wiring method.
Electrode: $19.95 Wire w/cage & boot: $8.50 per foot
|
Intermittent Pilot Control
This safety control is designed for indirect burner ignition and supervision. Used with a rectifying pilot, it provides spark ignition and flame monitoring with shutdown times under 1 second. Can be used with all fuel gases. This is a 24volt system designed to be used with 24volt solenoids.
Price: $117.50
|
UV Scanner
The C7027A Minipeeper is a compact flame detector for use with the Honeywell R7023C Flame Relay. The scanner detects ultraviolet radiation emitted by main flame or pilot flame. Mounting: 1/2" NPT nut for mounting to 1/2 sight pipe. Comes with 6 ft. Leads
Price: $149.00
|
Flame Detector Relay
This Honeywell Flame Detector Relay Series 7800 comes in many different models that will provide proven flame in many applications. Unit prices include sub-base and appropriate amplifiers. Used with an electric solenoid valve, it can provide 100% shut off in less than 1 second. This is an industry standard and is the safest means of flame monitoring and shutdown. 120 or 240 volts AC. Please specify.
Price: $899.00
|
|
|
